JMP User Community

Latest Discussions

Adding constraints to design with discrete factors

Hello,I am trying to add constraints to design with 4 discrete factors (X1,X2,X3,X4), where all the factors have 3 levels. What is the best way to add constraint to specify that three factors (X2,X3,X4) should add up to 97%? I am assuming I'll have to add disallowed combinations script option for this but not sure about the script.
billi

Discussions |
Feb 24, 2022 8:36 AM

976 views | 2 replies
Incorrect 95% confidence interval range for matched pairs plot?

I am trying to create a bland-altman plot using the matched pairs function in JMP. I created the plot below and decided to double-check some of the statistics calculated on excel. I found that while the standard error and mean difference were correct, my upper and lower 95% confidence interval values were very different than the ones provided by JMP Pro 16 I tried to test out their match pair exa...
Querida

Discussions |
Feb 24, 2022 8:25 AM

3320 views | 2 replies
MSA Gauge R&R AIAG Version?

Hallo!JMP Verion 16.1Vorrede zu meinen Daten:Ich möchte einen Datensatz (2 nahezu gleiche Messysteme, darauf jeweils die 10 gleichen Personen mit 5 Wiederholungen gemessen) auswerten und den Varianzanteil durch die verscheidnen Massysteme zu erhalten. Dazu kann ich ja Gauge R&R oder EMP zur Analyse verwenden. Da alles mit dem gleichen Bediener gemessen wurde, würde ich bei der Analyse die 2 Messys...
CountableMarten

Discussions |
Feb 24, 2022 8:23 AM

2251 views | 4 replies
How to reconcile prediction profiler confidence intervals with parameter estimates for mixture design

I have an mixture experiment with four components. It's a custom design of 16 runs with no replication that started with a model that included interactions of two factors and three components. The mixture constraint is that the four components sum to 1.0. The reduced model from the data has only the four main effects as statistically significant (p<.0001). The prediction profiler plots show 95% ...
MiBo

Discussions |
Feb 24, 2022 8:21 AM

5413 views | 10 replies
Feedback on Custom DOE to Predict Proportion of Rejectors

The BackgroundI recently ran a pilot study with 5 different food samples that have varied "Starch," "Sugar," and "Salt" as continuous factors. Each of the 5 food samples was tasted by 150 panelists each, who either accepted or rejected the sample. The percentage of rejecting panelists is what I would like to model as a function of my three continuous factors. My pilot study yielded some interest...
Shujinko

Discussions |
Feb 24, 2022 8:08 AM

2315 views | 5 replies

Previous
Next

Latest Discussions

Adding constraints to design with discrete factors

Hello,I am trying to add constraints to design with 4 discrete factors (X1,X2,X3,X4), where all the factors have 3 levels. What is the best way to add constraint to specify that three factors (X2,X3,X4) should add up to 97%? I am assuming I'll have to add disallowed combinations script option for this but not sure about the script.
billi

Discussions |
Feb 24, 2022 8:36 AM

976 views | 2 replies
MSA Gauge R&R AIAG Version?

Hallo!JMP Verion 16.1Vorrede zu meinen Daten:Ich möchte einen Datensatz (2 nahezu gleiche Messysteme, darauf jeweils die 10 gleichen Personen mit 5 Wiederholungen gemessen) auswerten und den Varianzanteil durch die verscheidnen Massysteme zu erhalten. Dazu kann ich ja Gauge R&R oder EMP zur Analyse verwenden. Da alles mit dem gleichen Bediener gemessen wurde, würde ich bei der Analyse die 2 Messys...
CountableMarten

Discussions |
Feb 24, 2022 8:23 AM

2251 views | 4 replies
How to set values for last 30 rows of a column?

Hi guys, I'm a complete scripting newbie here so please have patience with me . I have a data set with multiple columns and am trying to make a script that will automatically select the last 30 rows of a column and change the content from "baseline" to "CLCR". Please see my attempt: dt = Current Data Table(); dt1 = dt << Select Columns( :CLCR ); dt1 << select where( Row() > N Rows( dt ) - 30 ); d...
kkrog

Discussions |
Feb 24, 2022 1:07 AM

1493 views | 1 replies
Conditional If then to return values for ranges

I have written a formula to flag runs in campaigns (ex: consecutive days above 19.) HOw can I create a formula that will then generate the production values specific for campaigns greater than 9 days? (Examples: campaign 1, 2, 3=>No value whereas campaigns showing 1,2,3,4,5,6,7,8,9 would show the appropriate number 19,20,21,22,23,24,25,26,27 etc.)
ByrdQuestions

Discussions |
Feb 23, 2022 3:11 PM

1451 views | 2 replies
All possible models - what criteria are used to determine the order of independent variables retained by a model?

16.1.0Hi All, I've been experimenting with the All Possible Models option within the stepwise linear regression module. I was wondering what determines the order of the independent variables (IV) listed? Does the order infer some measure of effect/sensitivity, if so is there a way to identify what the relative sensitivity is? Thanks in advance. Cheers
Clint
RegressionOwl23

Discussions |
Feb 23, 2022 11:21 AM

955 views | 1 replies

Previous
Next

Latest Discussions

No table linking after saving the project?

Hi,when I generate a summary table with the option "link to original data table" (selected by default), the two tables are linked:By selecting a row in the summary table the corresponding rows in the original table are selected.Cool.This also works for selections in Graphs and Dashboards.Very cool! Now my problem:After saving both tables to a project file, (precisely: after close & re-open the pro...
hogi

Discussions |
Feb 3, 2022 4:19 AM

597 views | 0 replies
Setting Guardbands on Test Limits Using EMP

Hello. I am trying to use the EMP tool to help set guardbands to my test limits based on my gauge R and R data from a final test machine.I used 10 devices and measured these devices 5 times each, across 5 different test sites on the machine.I need to know how much to guardband my Upper and Lower specs. I am having trouble understanding how to apply the data in the EMP report. I feel like this is a...
Jbritsch04

Discussions |
Feb 2, 2022 8:49 AM

766 views | 0 replies
How to introduce lower bounds for simulated data in Profiler platform

Hi JMP community, (JMP Pro 16.0.0) I'm hoping to find out if there is a way to include lower bounds to simulated data in the Profiler platform. I have several predictors going into a model, but few data points to fit. So, in order to generate simulated ("synthetic") data, I use the Prediction Profiler platform along with the multivariate correlation structure of the data to generate thousands ...
SDF1

Discussions |
Feb 1, 2022 11:09 AM

588 views | 0 replies
Query Builder filtering on date stored in Varchar(20)

Query Builder - date filter.SQL ServerJMP version 16.2In the database (SQL Server) I get the Date field called RETURNDATE in ‘varchar20’ – I would like to use the Calendar functionality in the filter to select my dates I tried to create a calculated column (Calc1) and specify CAST([RETURNDATE] as date), which he doesn’t like. Using SQL outside Query BuilderSELECT TOP (1000) [LABJOBNO] ,[DESPA...
HansD

Discussions |
Jan 25, 2022 6:12 AM

1390 views | 0 replies
M1 Macbook Pro JMP Capabilities

Hi all,
I'm thinking about upgrading from my windows set-up and running a M1 Macbook Pro as my primary set up. I wanted to open up the discussion and see if any other JMP users were using the newest Macbook Pro and if they have run into any hurdles yet? I do a lot of R/Python integration. I do have a decent set up right now, but want to know if anyone else has tested out this connection and knows ...
MikeDereviankin

Discussions |
Jan 21, 2022 1:52 PM

789 views | 0 replies