Turn on suggestions

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for

- JMP User Community
- :
- Discussions
- :
- For loop for measurement system analysis

- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page

Highlighted

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Apr 13, 2020 6:06 PM
(769 views)

I write a script to generate GR&R (measurement system analysis). Script works fine but for every plot, it shows the pop up window (see below) and I have to click ok for all parameters. is there a way to by pass this ?

```
dt << set name("combine");
```

ColList = dt_spec << get column names (numeric);
obj = data table("combine") << manage spec limits (Y(eval(ColList)), load from limits table (dt_spec), save to column properties(1));
obj << close window;
close(dt_spec,no save);
new window ("GRR",
for (i = 1, i <= N items (ColList), i++,
variability chart (
Y ((ColList [i])),
X (:Tester,:Operators, :Parts),
Model ("Crossed"),
Analysis Type( "Choose best analysis (EMS REML Bayesian)" ),
Show group means (1),
Points Jittered( 1 ),
AIAG Labels( 0 ),
Show Box Plots( 1 ),
Mean Diamonds( 1 ),
Mean Plots( 1 ),
Name( "Gauge R&R" )(5.15),
Name( "Gauge R&R Report" )(1),
Automatic Recalc( 1 ),
)
);
);

1 ACCEPTED SOLUTION

Accepted Solutions

Highlighted

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Try adding "Historical Sigma(0)" inside the Variability Chart part of the script to see if that helps. For example:

```
variability chart (
Y ((ColList [i])),
X (:Tester,:Operators, :Parts),
Model ("Crossed"),
Analysis Type( "Choose best analysis (EMS REML Bayesian)" ),
Show group means (1),
Points Jittered( 1 ),
AIAG Labels( 0 ),
Show Box Plots( 1 ),
Mean Diamonds( 1 ),
Mean Plots( 1 ),
Historical Sigma(0),
Name( "Gauge R&R" )(5.15),
Name( "Gauge R&R Report" )(1),
Automatic Recalc( 1 ),
)
```

6 REPLIES 6

Highlighted
##

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: For loop for measurement system analysis

You script is confusing to me. It appears that you are getting the names of the columns to be analyzed from the dt_spec referenced data table

`ColList = dt_spec << get column names (numeric);`

But then close the data table before analyzing it

I believe the code for setting the spec limits should be

```
dt << set name("combine");
ColList = dt << get column names (numeric);
obj = dt << manage spec limits (Y(eval(ColList)), load from limits table (dt_spec), save to column properties(1));
obj << close window;
close(dt_spec,no save);
```

Jim

Highlighted
##

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: For loop for measurement system analysis

Hello @txnelson

Am not sure if am commenting on the correct post but I have a question I'd like your help with:

I have 2 tables:

Table 1: 'CadDataFromF31' that has 201 rows

Table 2: 'Fiducial 12 Measured from Fiducial 31' that has 10 rows

I would like to use these 3 columns: "File Name of Fiducial 31 Grouped", "c" and "s" from Table 2 and add to Table 1. The thing is, I'd like to do this with iteration. Meaning 10x of Table 1 [concatenated].... and have 3 additional columns from Table 2.

So the new table should have 2010 rows and 18 columns. Each group of 201 rows should have the same value for the last 3 columns as in the image below.

Could you help me with this?

Thanks in advance

Highlighted
##

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: For loop for measurement system analysis

Actually, I now see that this can be done with a 'Cartesian Join'.... Thanks nonetheless!

Highlighted
##

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: For loop for measurement system analysis

hi,

yes, i get the name from dt_spec for the analysis. i have no problem set up the spec.

The problem i have is when I plot the GR&R, for every graph, it will show a pop up window (see my original email) that I have to click ok.

Question : Is there a way to skip that pop up window ? so all graphs can be plotted without user clicking ok

Yanee

Highlighted
##

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: For loop for measurement system analysis

What if you change the option indicated by this launch argument?

`Analysis Type( "Choose best analysis (EMS REML Bayesian)" )`

Learn it once, use it forever!

Highlighted

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Try adding "Historical Sigma(0)" inside the Variability Chart part of the script to see if that helps. For example:

```
variability chart (
Y ((ColList [i])),
X (:Tester,:Operators, :Parts),
Model ("Crossed"),
Analysis Type( "Choose best analysis (EMS REML Bayesian)" ),
Show group means (1),
Points Jittered( 1 ),
AIAG Labels( 0 ),
Show Box Plots( 1 ),
Mean Diamonds( 1 ),
Mean Plots( 1 ),
Historical Sigma(0),
Name( "Gauge R&R" )(5.15),
Name( "Gauge R&R Report" )(1),
Automatic Recalc( 1 ),
)
```

Article Labels

There are no labels assigned to this post.