JMP User Community

Latest Discussions

GLM poisson plotting

I have been trying to generate an interaction plot after GLM poission regression on JMP 14.0, but I can not do it there. I have an experimental data with three way interaction, and want to present the value in plot. Any suggestions or ideas?
Sam_UT

Discussions |
Jul 2, 2021 9:29 AM

870 views | 1 replies
JMP script to create sequence column based on group from another source column

I have a large data set where the cycle changes over time. I would like to create a column that has an index by 1 at the start of each cycle and continues to count up until the next cycle starts then the counts starts back at 0. I have tried using the count and sequence functions shown below but I run into problems when my second cycle has more values that my first cycle (see diagram below where t...
thedellette

Discussions |
Jul 2, 2021 8:19 AM

2639 views | 3 replies
FDE model selection and fit. A 'Knotty' problem...

Hi All, I'm currently trying to explore some analytical data where the response changes over time using FDE. The context is that this is an analytical method where the response of the same sample(s) are changing over time. We used a surface-response DoE design in an attempt to capture the effect of the 2 main factors and identify what is causing this change.For each experiment in the design, we ad...
Jon_Armer

Discussions |
Jul 2, 2021 7:26 AM

2228 views | 3 replies
How to force a new best guess a column (modeling type and data type)

I am initiating a column as character containing empty values. Later on, this column will be populated with data from a data base that can be any type. By having characters no transformation is done by JMP. How can I force a new best guess via JSL?
FN

Discussions |
Jul 2, 2021 7:24 AM

1790 views | 3 replies
How do I Add Context to Text Explorer Results?

I am new to JMP and just starting to use the Text Explorer to look for insights in free text responses from consumer research studies. Once the analysis has identified the key terms found in the responses is there an automated way to look at the most common context for each term? For example if the consumer study was looking at the performance of a new paper towel we would expect the term "absorb"...
MKinninmonth

Discussions |
Jul 2, 2021 2:03 AM

1407 views | 2 replies

Previous
Next

Latest Discussions

GLM poisson plotting

I have been trying to generate an interaction plot after GLM poission regression on JMP 14.0, but I can not do it there. I have an experimental data with three way interaction, and want to present the value in plot. Any suggestions or ideas?
Sam_UT

Discussions |
Jul 2, 2021 9:29 AM

870 views | 1 replies
FDE model selection and fit. A 'Knotty' problem...

Hi All, I'm currently trying to explore some analytical data where the response changes over time using FDE. The context is that this is an analytical method where the response of the same sample(s) are changing over time. We used a surface-response DoE design in an attempt to capture the effect of the 2 main factors and identify what is causing this change.For each experiment in the design, we ad...
Jon_Armer

Discussions |
Jul 2, 2021 7:26 AM

2228 views | 3 replies
How to force a new best guess a column (modeling type and data type)

I am initiating a column as character containing empty values. Later on, this column will be populated with data from a data base that can be any type. By having characters no transformation is done by JMP. How can I force a new best guess via JSL?
FN

Discussions |
Jul 2, 2021 7:24 AM

1790 views | 3 replies
How to configure factors when another factor depends on each other

Hello, I'm fairly new to this community. I'd really appreciate any help you can provide! I'm trying to construct a classical screening DOE, but my factors are a bit funny..My process is a calendaring process, where the gap between two rolls can be adjusted in 2 ways: mechanically or hydraulically.Mechanically setting it means there is absolutely no give, while hydraulic adjustment has a little giv...
merkis

Discussions |
Jul 1, 2021 12:59 PM

3522 views | 5 replies
Excluded Cols still plotting when I run a script, but not when I plot it manually?

So not sure what to is going on here. I'm trying to plot this Group of cols, with several excluded. If I manually launch the FitYbyX, those excluded columns don't even show up in the pop-up and thus don't get plotted. However, when I run this script telling it to plot that Column Group, it still plots the excluded Columns. What's up with this? dt= current data table(); ow2 = Oneway( Y( dt<<get...
aliegner1

Discussions |
Jul 1, 2021 10:39 AM

1029 views | 2 replies

Previous
Next

Latest Discussions

Section 508 compliance

Is there any guidance on how to make JMP graphs section 508 compliant (ADA issue for government documents)? I found a post on how to remove the gray background, but is there any 508 specific guidance or other preference settings that would be helpful? Maybe this is a wish list item?
GGfGA

Discussions |
Jun 30, 2021 10:03 AM

875 views | 0 replies
Multi File Import of network folder slower in latest JMP version

Hello, In JMP 14, Multi File Import of a network folder was relatively fast. For example, it takes ~11 seconds to load the below folder. With JMP 16 on the same computer/folder/network, it will first spend almost 3 minutes while "discovering files", before proceeding with the above "loading file names" step. Are there any settings or options that I could change to skip the "discovering files" step...
jach

Discussions |
Jun 22, 2021 11:06 AM

731 views | 0 replies
ODBC Hive connection, change container size in the script?

Wondering if anyone can help here. I am trying to write some JMP scripts that SQL query data from a hive table. I need to change the container size and am told that I should just "do it in the connection settings". I was told that in python, you just add a configuration={"hive.tez.container.size":'10240'} parameter to the hive.connect call. How would I do this through JMP? I already have the Cloud...
aliegner1

Discussions |
Jun 17, 2021 3:43 PM

971 views | 0 replies
Using a List to Filter in Custom Query Builder - Question

Hello, I would like to use a list to filter within a continuous column in Query Builder. Range and then join does not work as my data set from my database will be tens of millions of lines, so I would like my list to be the only thing queried. I would like to use a list (I have a separate data sheet with the column) of about 40 or so unique numerical values and use that in the filter for a custom ...
Benjamin_S

Discussions |
Jun 3, 2021 7:59 AM

1273 views | 0 replies
Can I control text size in a word cloud inside a dashboard container?

Hi all,I have a dashboard with a data filter, a map, and a word cloud that looks like image 1 below. I have two formatting issues with the word cloud I'd like to fix. First, by design, when I make different selections using the data filter, the subset of records that are shown in the map changes and the word cloud applies only to that selection. However, when I change the data filter selection, th...
caseylott

Discussions |
Apr 28, 2021 12:03 PM

1264 views | 0 replies