turn on suggestions

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for

- JMP User Community
- :
- Discussions
- :
- Discussions
- :
- Re: Sample Size Calculation

Topic Options

- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Aug 21, 2016 12:29 PM
(4347 views)

My current process is operating at a 0.01 defect frequency (e.g., 3 defects in last 300 units inspected). If I make a process change that could potentially increase the defect frequency, how many units will need to be inspected post-change to determine if a statistically significant difference in defect frequency?

1 ACCEPTED SOLUTION

Accepted Solutions

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Aug 24, 2016 6:35 AM
(5667 views)
| Posted in reply to message from rmarkdavis1219 08/21/2016 03:29 PM

Mark:

Here is a good formula for the AQL sample size and the RQL sample size The sample size, 947 or 948 is shown.

I would have sent you the JMP table but don't know how to post it here

9 REPLIES

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Aug 22, 2016 7:29 AM
(4149 views)
| Posted in reply to message from rmarkdavis1219 08/21/2016 03:29 PM

Mark:

With the current process at 1% defective you have to set a upper defective limit say 2%. Also, the risks have to be assigned, typically 10% for type I & II errors

The sample size is than the sample size and defect value which will accept a 1% or lower defect level 90% of the time while rejecting the product when the relect level is 2% or higher 90% of the time.

An OC curve is the best way to visualize the results

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

You will also need to articulate 'delta'...or what is the minimum defect rate improvement that you are trying to detect.

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Mark:

My Excel based calculation says a sample of 948. If there are 13 or less defects, accept that there is no process shift, greater than 13 defects a shift has occurred, given the risks specified.

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Hi,

Can you please send the table as attached file.

Thanks

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Aug 22, 2016 11:36 AM
(4149 views)
| Posted in reply to message from rmarkdavis1219 08/21/2016 03:29 PM

I suggest you use a Runs Chart and/or Process Behavior Chart (Control Chart), With this type of "rare event" data, both work well. Use "good units inspected between defective units" as your test variable. When you make your process change, you will be able to detect a shift in performance, if there is one. See my article in Quality Digest regarding OSHA Recordable Injuries (same type of data)...http://www.qualitydigest.com/inside/quality-insider-article/alleviating-tortured-data.html

Steve

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Aug 24, 2016 6:35 AM
(5668 views)
| Posted in reply to message from rmarkdavis1219 08/21/2016 03:29 PM

Mark:

Here is a good formula for the AQL sample size and the RQL sample size The sample size, 947 or 948 is shown.

I would have sent you the JMP table but don't know how to post it here

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

FYI (and regarding 'but don't know how to post it here') - If you use the 'Advanced Editor':

there's an 'Attach' link at the bottom right.

Highlighted
##
##### Re: Sample Size Calculation

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Thanks for the tip ! !

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

I am having trouble with this formula for low rejection rates, e.g. AQL 0.1% RQL 0.25% . Any ideas? Curious about the use of Chi sqaure quartile vs binomial, etc

@vinkane wrote:Mark:

Here is a good formula for the AQL sample size and the RQL sample size The sample size, 947 or 948 is shown.

I would have sent you the JMP table but don't know how to post it here