Turn on suggestions

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for

- JMP User Community
- :
- Discussions
- :
- Discussions
- :
- Need help understanding interaction variable

Topic Options

- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Feb 17, 2012 10:10 AM
(8232 views)

Hello

I am trying to conduct a simple 2 way analysis of an experiment; each factor has 3 levels with one replicate each. Both variables are continuous. When running the analysis and looking at the output and parameter estimates I see the following:

Intercept

Factor 1

Factor 2

(Factor 1 - x) * (Factor 2 - y) where x and y seem to be some averaged/arbitrary value

Can somebody explain how I would use (Factor 1 - x) * (Factor 2 - y) in the regression equation?

Also, what is the best way to determine which levels of the different factors are most significant.

thanks

2 ACCEPTED SOLUTIONS

Accepted Solutions

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

First after fitting your model go to the red triangle and choose save columns> "prediction formula"

This saves the prediction formula for your model to the data table.

Go to your JMP data table and you will notice that a new column has been added at the far right named prediction formula

Double click on the column heading and a dialog box will appear.

Under the column properties pulldown highlight Formula

click edit formula button

go to the red triangle pulldown and chose simplify

That will give you the simplified parameter estimates.

The reason you obtained strange parameter estimates was because you probably chose a 3 level design. You could have accomplished the same thing with a two level design and just added center points which might have been simpler.

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

You are correct. The null is due to the fact that all of your degrees of freedom are used up. That is why I asked you if they could be treated as continuous. Did you try to model using the stepwise model personality?

5 REPLIES 5

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

First after fitting your model go to the red triangle and choose save columns> "prediction formula"

This saves the prediction formula for your model to the data table.

Go to your JMP data table and you will notice that a new column has been added at the far right named prediction formula

Double click on the column heading and a dialog box will appear.

Under the column properties pulldown highlight Formula

click edit formula button

go to the red triangle pulldown and chose simplify

That will give you the simplified parameter estimates.

The reason you obtained strange parameter estimates was because you probably chose a 3 level design. You could have accomplished the same thing with a two level design and just added center points which might have been simpler.

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Need help understanding interaction variable

I understand now, thanks.

One other question... If I have a data set with 2 factors, but there is only 1 replication/observation (as shwon below), I can't do any interaction analysis because of inssuficient DoF, correct??

Factor A Factor B Response

1 a y1

1 b y2

1 c y3

2 a y4

2 b y5

2 c y6

3 a y7

3 b y8

3 c y9

Highlighted
##

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Need help understanding interaction variable

You should be okay. If the are both 3 level categorical factors the model is pretty saturated but you get the interactions terms delineated. You could also try a stepwise regression to make the model more parsimonious. If one factor is continuous and one is categorical then it appears to me when utilizing the "simulate responses" under the red triangle that you have enough DoF for interactions and the error. Alternatively you could also add an additional row and replicate one of the other combinations.

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Need help understanding interaction variable

The 2 factors are quantitative, but can be classified as Nominal.

The reason I asked is because when I run the fit model command with the 2 factors and the cross of the 2 factors as a the model effects, the F test for the model's effects are null. I think it's because each factor has 2 degree of freedom and the interaction has another 4, which makes 8 degrees of freedom. This leaves no degrees of freedom for the error term which is why the F test can't show any results. Isn't that right? If I run the ANOVA without the interaction terms it runs fine. And if I changed one of the factors to a continuous variable it runs fine, but I think in my case they should both be set as nominal.

I was looking online and it seems that as a general rule you cannot properly analyze the interaction between 2 factors with only 1 replicate/combination. I just would like to be sure about this fact.

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content