Turn on suggestions

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for

- JMP User Community
- :
- Discussions
- :
- JMP12 DOE - Reducing a trial plan to the most relevant data points

- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

JMP12 DOE - Reducing a trial plan to the most relevant data points

Mar 3, 2016 10:06 AM
(7294 views)

Hello to the Community,

i´m new here, so i´ll get right to it:

I have created the attached experimental design with JMP12 and performed my experiments according to it.

In the following it turned out, however, that an evaluation of all 90 samples would be too expensive/time consuming, which is why now I will be evaluating only a subset of 30 samples. As a result, I will probably get rid of third-degree interactions.

In order to choose 30 out of 90 samples: Is there a way to filter out the most relevant data points/specimens for such a reduced evaluation?

Working with a new created smaller plan does not work, since the combinations are different. The 90 specimen already exist and there is no possibility to redo the whole

experiment with a new plan :/

Thank you very much in advance!

Lingo

9 REPLIES 9

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: JMP12 DOE - Reducing a trial plan to the most relevant data points

Hi Lingo,

If you load in your factors as covariates, it will choose from the rows in your original experiment. Under the "Add Factor" button, choose Covariate with your data table open (to get a rough idea, I used covariates in this example).

When you get to the run size, change it from 90 to 30.

You'll have to make a decision on the model - even for an RSM you need 35 runs (and covariates are not playing nicely with if possible terms, I'll have to look into that).

I'm not sure how you're planning to model the results (since you have more terms in an RSM than you do runs), but for the design you could try removing some different sets of terms, create a few different designs and compare them in design evaluation. A choice that might end up being desirable and worth comparing is to have the main effects and quadratic effects in the model, and choose an alias optimal design.

Good luck!

Ryan

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: JMP12 DOE - Reducing a trial plan to the most relevant data points

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: JMP12 DOE - Reducing a trial plan to the most relevant data points

Hi Lingo,

I took a quick peek at your design. What you want to do (subset of 30) will require a more simplified model than simply sacrificing the 3rd order terms (3-way interactions and cubic terms). Just to estimate a main effects (1st order) and 2-way interaction model would consume all available degrees of freedom (ie the design would be saturated) in a 30 run subset. In such a case, you would not have any left over df to estimate error. You received great advice from Ryan. It is possible to bring in your existing design identifying all your factors as covariates. In this case your existing 90 run design will be the candidate set from which algorithms can select the most balanced 30 run subset for a much more simplified model of your choice. The question is whether any 30 run subset is "rich enough" in information to estimate your chosen model. One of the complications is that your candidate set has excess levels for most factors (5 levels for first 5 factors) than really will be needed for an estimable simplified model. So although one might normally think of a 90 run candidate set as "rich enough" to select a 1/3 subset, your 90 runs may not cover the 7 dimensional space as thoroughly as compared to a full factorial candidate set. Although I think you can likely come up with a reasonable approach for those 30 runs, I think you should be realistic in expecting some colinearity for most any simplified model. Of course the real beauty of JMP's DOE capability is that you can easily see that in the "color on correlation map" in the "evaluate design" or when you do algorithmically select the subset. You can also see the "correlation of estimates" in the "fit model" report by doing a dummy analysis on a Y with random data before actually committing to measure the subset. best of luck

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: JMP12 DOE - Reducing a trial plan to the most relevant data points

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: JMP12 DOE - Reducing a trial plan to the most relevant data points

Thank you all for your quick responses,

i am still a newbie, so i´ll try to work myself through it

peter.bartell@jmp.com unfortunately i do not have the Pro Version, it´s "just" JMP 12.1

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: JMP12 DOE - Reducing a trial plan to the most relevant data points

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: JMP12 DOE - Reducing a trial plan to the most relevant data points

Lingo had asked me separately about the 35 run design that can fit the RSM model, so I'll describe step-by-step details here in case anyone else comes across this thread.

With the original data table open

select DOE->Custom Design

from the Add Factor button, select Covariate

choose the first 7 columns (which were the factors), and click OK

click continue to the next screen

under model, click the RSM button

at the bottom, change the Number of Runs to 35 (from 90)

click Make Design

You should now get a 35 run design that can fit the full RSM model. Note there's no degrees of freedom left to estimate the error, so you'll probably be doing some type of model reduction, but at least you know everything there can be estimated.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: JMP12 DOE - Reducing a trial plan to the most relevant data points

Hey Ryan,

thanks a lot again

Tried it several times, always ended up with 48, closed and restarted then ended up with your 35

Super happy now!

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Get Direct Link
- Email to a Friend
- Report Inappropriate Content

Re: JMP12 DOE - Reducing a trial plan to the most relevant data points